What size wire and breaker should I use to run a 2 ton Goodman heat pump unit?
Dec 13, 2008 by jam4cs | Posted in Do It Yourself (DIY)
I have a Goodman heat pump part that I have purchased and the manual does not give vary convincing wiring examples. I have talked to people and they say that 12-3 with a 30 amp breaker will drudgery is this true?
Look at the amperage rating on the section. A 30 amp circuit requires a MINIMUM of #10 wire. #12 is for a 20 amp or less ambit. If the unit requires 240V 30A, you will run either 10-2 or 10-3, depending on whether the module requires a neutral, for 50 feet or less from the panel. If it's more than 50', run #8-2 or 8-3. If you use 10-2 or 8-2 (no non-combatant), each conductor will be connected to one pole of a 2 pole breaker. The Caucasoid will need to be taped or otherwise marked to indicate that it is a hot, not a disinterested. If you are unsure whether the neutral is needed, run 3 conductor. They can always permission the white disconnected and just use the black and red. Longing this helps.
woodtick314 | Dec 13, 2008
goodman heat pump wiring help?
Jul 26, 2007 by James D | Posted in Do It Yourself (DIY)
I have a Goodman heat pump and can't find a wiring diagram to place a new thermostat. I have a Honeywell non-programmable digital thermostat that I have a yen for to install. I have a red, blue, green, white, orange, and yellow wires coming out of the barrier.
Throw away it and get a Carrier
Fat, Old, but Honest | Jul 26, 2007
Outside heat pump Goodman CPLJ48 does not work, what is the problem?
Nov 20, 2007 by NorthCarolinaNow | Posted in Maintenance & Repairs
When I beat it on the thermostat to "Heat" position I announce that the fan on the heat pump, CPLJ48, does not run. What is the most possible facer? Could a fuse blowout?
If your core circulating air blower runs but the fan on the outside heat pump component does not run it is most likely a fuse or circuit breaker because they are on split circuits. If that is the case check the main boundary breaker and also look for a fuse inside the juncture box where the flexible power conduit enters the brothel from the outdoor heat pump unit.
pyro_alchemist | Nov 21, 2007
i have a goodman heat pump the fan will barely start turning w/o assistance. coil? or fan motor?
Oct 15, 2007 by robert w | Posted in Maintenance & Repairs
no swop in heat or air
This is lately a word of advice that I wish I had given myself.
Don't ever huge quantity with goodman. I had a Janitrol heat pump that I had to replace the compressor at least five times. Then, I had to get a new one. Since my renew person deals with Goodman, I got another Janitrol.
Goodman has a bad reputation. I wrote to the them about my problems. I got no answer. When I contacted a regional representative, he told me they had told him not to answer.
Counselor | Oct 15, 2007
I'm looking for a diagram to show me where the contactor is on a smaller goodman heat pump?
Apr 26, 2008 by Martin C | Posted in Maintenance & Repairs
It's just now one that they put on a one story 1300 sq. ft. track home.
Echo the power wiring that comes in to the unit.
The wires go anon to the contactor.
The wiring diagram that is on the control cubby-hole cover should verify that.
gizmoe | Apr 26, 2008
: $599.00 
Waterless Fracking Method Targets Natural Gas Industry's GazeBy Matt Goodman, CBSDFW.com New York Senator Tony Avella speaks at a news conference and rally against hydraulic fracturing, also known as fracking, in New York State on January 11, 2012 in New York City. The event, which was held on the steps of City and more »